LackRack

This is a really neat trick I just read about. LackRack is the ultimate, low-cost, high shininess solution for your modular datacenter-in-the-living-room. Its low-cost and perfect fit are great for mounting up to 8 U of 19″ hardware, such as switches (see below), or perhaps other 19″ gear. Featuring the LACK (side table) from Ikea, the LackRack is an easy-to-implement, exact-fit datacenter building block. Installing hardware in your LackRack is easy! Screw all the screws that fit in the rack mount in the left and right leg. The table legs have just right dimensions for almost 9U of rack space for 19″ hardware.

Earlier some hifi people have built hi-fi stand made out of IKEA Lack side tables, but now the world is ready for 19″ networking equipment racks. Check LackRack home page for more information on how to build your own very cheap 19″ rack system. The page also tells that also Ikea LACK coffee table and Ikea ODDA night table have right dimensions and can be easily converted to cheap 19″ racks.

400px-LackRack

Image source: http://wiki.eth-0.nl/index.php/LackRack

21 Comments

  1. Vince Kesselman says:

    I’d like to thank you 4 your insightful posts.

    Reply
  2. making wooden fishing lure says:

    Thank you for another fantastic blog. Where else could I get this kind of information written in such an incite full way? I have a project that I am just now working on, and I have been looking for such information… Regards…

    Reply
  3. Jon Brink says:

    I read AV Guide’s opinion about this very thing. Couldn’t agree more with you and less with them.

    Reply
  4. Awwal says:

    I stumbled on your own website by accident whilst searching Yahoo and I’m glad I did. Your publish is often a bit varied and I liked browsing it. I will consequently make a comment about it on my weblog and level my customers your way. Thank you.

    Reply
  5. Mareena says:

    Hey There. I found your webpage looking with yahoo. This is a particularly well prepared short article. I’ll be sure to bookmark it and return to look at far more of your respective helpful info. Thank you for sharing it. I will positively be back again yet again.

    Reply
  6. Tadeusz says:

    Hi there We’re so delighted We uncovered the web-site, I unquestionably noticed u by error, whilst We was searching within just Aol in relation to something totally different, However I am the following and We’d obviously choose to state cheers for that wonderful posting additionally a over-all entertaining blog site

    Reply
  7. Solanda says:

    ome really good things on this blog , I benefit from it.

    Reply
  8. Josh Channer says:

    Many of these comments remind me of the hysterical lady around the Simpsons who always screams…

    Reply
  9. Tomi Engdahl says:

    Here is another rack mounting idea:

    Workshop and Workbench Update
    http://blog.rhysgoodwin.com/home-diy/workshop-and-workbench-update/

    My favourite part…What would a workshop be without a server……tool drawer.

    Reply
  10. Tomi Engdahl says:

    A do-it-yourself instrument cart
    http://www.edn.com/design/test-and-measurement/4421703/A-do-it-yourself-instrument-cart

    When I want to use an oscilloscope, signal generator, and other instruments, I must rearrange the “clutter” on my lab table to make space. I’d rather put my instruments on a cart and place them near the table only when I need them. eBay listed several used Tektronix scope carts, but most cost several hundred dollars, and shipping would have cost about the same.

    Reply
  11. Tomi Engdahl says:

    IKEA LED Table Mod Doesn’t LACK Awesome
    http://hackaday.com/2014/02/03/ikea-led-table-mod-doesnt-lack-awesome/

    [Klaas] has turned a LACK Side table into an interactive LED table featuring 144 RGB LEDs.

    Reply
  12. Tomi Engdahl says:

    Why use standard data center racks in your home, when you can house gear in a stylish side table from IKEA?
    http://www.datacenterknowledge.com/archives/2014/08/27/the-home-data-center-mancave-for-the-internet-age/2/

    Reply
  13. Tomi Engdahl says:

    19″ racks have no dimensions that are actually 19″. Also 2x4s aren’t 2 inches by four inches. Somehow, a 2×4 server rack works.

    Ultra Simple 2×4 Server Rack
    http://hackaday.io/project/318-ultra-simple-2×4-server-rack

    It doesn’t get any easier or cheaper than this. Build a 4ft tall server rack from 2×4 BigBox hardware lumber.

    This project uses four cheaply available 2×4 boards and assembles them into a 4-foot-tall rack mount frame, suitable for housing generic 19″ rack hardware. Wood is great: it’s abundant, light, and strong. Heck, it even grows on trees!

    Probably the biggest selling point of this setup is that it can be assembled for under $20.

    Define: 19″ Rack
    http://www.server-racks.com/19-rack.html

    Reply
  14. Tomi Engdahl says:

    Other use for Lack:

    IKEA Table 3D Printer
    http://hackaday.com/2016/12/22/ikea-table-3d-printer/

    In this Instructable, [Wayne Mason-Drust] shares the step by step guide on how to make a cool, good-looking, 3D printer based on the Ikea LACK table. From an Ikea lantern weather station to a fully printed CNC based on an Ikea table, it’s almost safe to say that a 3D printer Ikea hack was overdue.

    The idea to use a Ikea table as a base for a 3D printer first came to [Wayne] as he used this table to support other 3D printer he had working in his business.

    PRINTTABLE the Affordable, Attractive IKEA Lack Table Hack to create a 3D Printer
    http://www.instructables.com/id/PRINTTABLE-the-Affordable-Attractive-IKEA-Lack-Tab/

    Reply
  15. Tomi Engdahl says:

    Does anybody know what a rack screw actually is? Size?

    The standard (EIA-310-D) sets it as 10-32 or 6mm if tapped or square for inserts. But I imagine there may be stuff out there not set to the standards …

    10-32 is most common in AV applications. But 12-24 is common in data applications.

    But the heads can be Phillips, Robertson, torx, security torx, even flathead.

    Reply
  16. Tomi Engdahl says:

    Rackmount Hardware Placement Issues? IKEA LACK To The Rescue!
    https://hackaday.com/2022/05/29/rackmount-hardware-placement-issues-ikea-lack-to-the-rescue/

    You can buy a whole lot of cheap hardware in 19″, and arguably, that’s where you can get the best hardware for your dollar. Many a hackerspace has used these tables for makeshift infrastructure, permanent in all but intent. So, in case some of us missed the memo, now you are aware of yet another, underappreciated solution for mounting all these servers we get for cheap when yet another company replaces its equipment – or undergoes a liquidation. If LackRack hasn’t been on your radar – what have you been using for housing your rackmount hardware collection?

    https://wiki.eth0.nl/index.php/LackRack

    Reply

Leave a Reply to Solanda Cancel reply

Your email address will not be published. Required fields are marked *

*

*