Just about all professional equipment uses balanced audio lines, which, if properly executed, will eliminate the hum completely. They help especially with long interconnects where earth loops can be a real pain. Circuits driving balanced lines must themselves be balanced to maintain the benefits of balance. This may be achieved by differential signaling, transformer coupling or by merely balancing the impedance in each conductor. Typical professional audio sources, such as microphones, have three-pin XLR connectors. One is the ground or common, while the other two are signal connections.
Many consumer HIFI equipment and other audio signal sources offer only unbalanced outputs. Unbalanced interconnections pick up easily all kinds of noise (especially ground loop noise), so you might want to avoid them everywhere you can.
You can convert the simple unbalanced preamp output to balanced circuit with one of the following tricks:
- Use a DI box to convert unbalanced signal to balanced microphone level signal
- An audio transformer is a classic way to convert unbalanced to balanced
- Balanced opamp output circuit can convert unbalanced to balanced (more modern approach but more components)
In addition to those there is not so widely mentioned impedance-balanced output option:
1. Figure out the output impedance of your unbalanced signal source. Usually looking at the circuit diagram of the device will tell you that easily. If you don’t have that, you can always measure the output impedance.
2. Pick a resistor that has same resistance as the output impedance of your unbalanced output (as close as possible… preferably within 1% accuracy).
3. Wire the unbalanced output signal to XLR pin 2 (+).
4. Wire ground to XLR pin 1 (ground).
5. Wire that resistor you just selected between XLR pins3 (-) and pin 1 (ground).
Now you have a impedance-balanced output. It is not exactly as good as a real balanced output, but performs pretty close a real balanced output in normal applications. You can use the same idea also with 6.3 mm jacks: signal goes to tip and the resistor to ring. An impedance balanced output with 6.3 mm jacks works as well as an unbalanced output if that is what is needed (just plug in a cable with mono plug).
Impedance-balanced principle has been used some professional electret mics and on outputs of some “budget” mixers! Just by adding one resistor an unbalanced output is converted to impedance balanced output that works very well with all equipment that has balanced inputs.
More information on line balancing and theory can be found at great The Self Site Balanced Line Technology document.
24 Comments
tomi says:
Propably not. The web address you gave on your posting just gave the following text:
We’re sorry!
This offer is not available in your area.
You will be redirected shortly.
So your link was to some stupid advertising campaign page… so I removed that from your post.
olympus digital voice recorder says:
olympus digital voice recorder…
I want to disagree with you, but tastes differ. Sample at least your post titled Unbalanced to impedance balanced ” Tomi Engdahl’s ePanorama blog…
online cna classes says:
Valuable info. Lucky me I found your site by accident, I bookmarked it.
Eldon Hinkle says:
Make an impression on We’ve to express that is wonderful. Even writing that send have to have taken you a seriously lengthy time. Thanks for ones effort!
Mary says:
Thanks for the detailed information! Everything is clear and understandable. Everybody will be able to use the info for his/her benefit following the provided guide!
Jon Brink says:
Are there too many audio shows out there? Or are there not enough?
Jon Brink says:
I think audiophiles need to worry less about the perfection of sound and instead try to immerse himself (or herself) in the music.
Efrain Sorenson says:
Lovely site, would love to see a bit more content though! A+
Ursula Plover says:
Hai, i am the admin of bleucheesefencing.com .Thank’s for sharing this info.This is very helpful and informative material.Good post and keep it up friend.
Mitzi Schleis says:
Hey friend , Why dont u put facebook badge on your site? Because I want to add your fb. Thanks Regards Admin of redstair.org
Ollie Dentler says:
Wow, great blog.Thanks Again. Fantastic.
Jon Brink says:
What shows do you go to? RMAF? CEDIA? CES? High End Show? California Audio Show? Capital Audiofest?
Karty Kredytowe says:
I just sent this post to a bunch of my friends as I agree with most of what you’re saying here and the way you’ve presented it is awesome.
Jon Brink says:
I love Wilson Audio. I actually own the very first production pair of Wilson Audio Tiny Tots (WATTs).
Chadwick Fenderson says:
what time? and do u suggest a selected microphone u enjoy cuz im thinking of accomplishing a household studio…? xoxo
Jenniffer Debaecke says:
Thank you for another fantastic article. Where else could any person get that kind of information in such a ideal way of writing? I have a speech next week, and I was looking for more info
Ressie Verant says:
This site is so great that i will honor it with my comment
Nolan Grilley says:
Hallo Dude , i like w/ u article.
Anglea Hoage says:
Anyways story short, you have written very nice post, makes me crack a smile.
dududukkkkkkk says:
Nice post at Unbalanced to impedance balanced Tomi Engdahl’s ePanorama blog. I was checking constantly this blog and I am impressed! Extremely helpful info particularly the last part
I care for such information a lot. I was seeking this particular info for a long time. Thank you and best of luck.
Lee Konkol says:
I simply want to say I am all new to blogs and honestly enjoyed you’re web page. Probably I’m want to bookmark your website . You certainly have fabulous article content. Thanks for revealing your web page.
Tomi Engdahl says:
Balanced (?) audio line receivers and the physics of fields
http://www.edn.com/electronics-blogs/analog-ic-startup/4403059/Balanced—audio-line-receivers-and-the-physics-of-fields?cid=Newsletter+-+EDN+on+Analog
trik sulap says:
Now you have a impedance-balanced output. It is not exactly as good as a real balanced output, but performs pretty close a real balanced output in normal applications.
Tomi Engdahl says:
Mixing balanced and unbalanced audio
https://www.youtube.com/watch?v=xFHB1LiLwaU
What happens when you mix single ended equipment with balanced audio gear?