The idea if replacing fluorescent light bulbs with LEDs seems to become popular. There are different kind of products made for that purpose. LED bulbs utilizes large arrays of high power LEDs to provide up to provide light. They are at best an economical way to replace commonly used fluorescent tubes.
Since introducing LED based fluorescent tube replacements more than a year ago, I have read that a plenty of low quality LED tubes hit the market. Unfortunately these are cheaply made at best and dangerous at worse.
Fluorescent fixtures are designed to support a specific types and size of fluorescent tube. Make sure that the LED replacement tube lights are the correct size for the fixture. Also, always remember that when servicing a fluorescent fixture or lamp for any reason, electrical power to the entire fixture should be disconnected.
A fluorescent tube is incorporated into a fluorescent lighting system which consists of two or three main components: (1) the fluorescent lamp (fluorescent bulb or tube), (2) the ballast, and (3) the starter system. When the fluorescent lamp is replaces with LED bulb usually some modifications are needed to the lamp wiring to make everythign work. In the simplest case that modification could be just leaving out the starter. At some other cases that could mean you need to rewire some part of the lamp wiring (which makes using normal bulb not possible anymore and can at worst case cause hazards).
LED Tube Light Installation Made Simple article tells that if the fixture has an electronic ballast, you only need to remove that and then wire the power directly to the lamp holders, completing one circuit for each bulb. If you have an older fixture with a magnetic ballast and starter, you usually will have to remove or open the starter and remove or short the magnetic ballast. There are also some LED tubes that can live with a traditional magnetic balast installed as it is normally (just remove the starter), but the downside of this design is lower efficiency (there are losses caused by the magnetic balast).
Led T8 Fluorescent tube lighting Circuit Connect Diagram shows the idea after the modification:
The two pins at each end of the LED bulb are connected together. Simply apply one side of the 120 Volts AC to one end of the Tube (either pin) and the other side of the 120Volts AC to the other end. The Ballast and the Starter must be Bypassed/Removed. This is critical that the ballast & starter is bypassed.
LED Vs. Fluorescent Lighting article tells that LED lighting and fluorescent lighting are just two of the types of lighting technologies available. Both have their own sets of advantages and disadvantages. One key area that they differ in is the area of energy consumption and lifespan. Both types of lighting are energy efficient when compared to traditional incandescent bulbs. However, LED technology costs more than CFL and fluorescent lighting. LED lighting (when well designed and built) can last upwards of 60,000 hours before needing to be replaced. Fluorescent lighting, particularly CFL bulbs, can last around 10,000 hours before needing to be replaced. LED light bulbs use about half the wattage of fluorescent lighting.
LED ‘Fluorescent’ Tubes article tells that a bad ballast can ruin lights and cause premature replacement, besides using the ballast to up the voltage just to drop it again seems ineffiecient. But this allows a transition to LED technology without a change in infrastructure. I think this this could be a very important step, considering the amount of fluorescent lights being consumed nowadays. Power consumption is about 50% of fluorescent bulbs and your replacement period becomes 10+ years so there are huge long-term savings. The main problem with this type of product is the huge upfront cost. We all know that 10 years from now (maybe much sooner on this fast developing field) there will be a much better alternative to this product so it is hard to justify the long-term commitment. Most cheap LED fluorescent tubes available nowadays can’t be used as a fluorescent tube replacement since they are dark, they give less output than the original fluorescent tube. There are very few LED tubes which are actually as bright or brighter than conventional fluorescent tubes. The cheap LED lighting (around US$40 to US$60) typically use cheap good old 5mm LEDs and most of them have heat sink problems. This will lead to over heating of LED bare chips and bullet shaped resin so they will not last very long. At the end of the day LED Fluorescent tubes should look like fluorescent tubes and alot of what I have seen offered within the market looks like a tube full of LED’s.
36 Comments
Pod Light says:
I really loved this post. You write about this topic very well. Wouldn’t it be great if you had a light that would automatically light up your purse interior as soon as you reach into your bag? A light would make it ideal when looking in your purse in dimly lit theaters, night clubs, restaurants and vehicles.
Cristobal Demian says:
Hi. I read a few of your other posts and wanted to know if you would be interested in exchanging blogroll links?
Here is my blog: Power supply manufacturer
Power supplies manufacturer
12W power adapter
Switching Power supply
Proper Maintenance of Hydroponic SuppliesGardening Equipment | Gardening Equipment says:
[...] LED tubes [...]
Kandi Cahall says:
This really a truly well thought out post. I certainly enjoyed reading it. Thanks
Buixrinuh says:
I enjoyed reading your blog ~ thanks for posting such useful content.
Buixrinuh says:
I enjoyed reading your blog ~ thanks for posting such awesome content.
hoodia says:
I will use your advice from now on. Mike
Stuart Alston says:
Sound good. Its also my favorite topic.That’s great andthanks for the fine sharring.
Trance Music says:
I definitely agree with the whole thing. Took me a while to read but it was well worth it. Im gonna read through a few other posts on this site and see if theres anything else thats good like this
Trance Music says:
Hi, I love Trance Music . I even wrote about it on my blog at http://www.trancecommunity.com/Forum/ a while ago. Anyway, I’m not necessarily into this stuff but LED tubes Tomi Engdahl’s ePanorama blog just happened to grab my attention there in the sidebar, while I was browsing through.
Tomi says:
Take a look:
What’s inside: LED tube light teardown
http://www.edn.com/blog/PowerSource/39514-What_s_inside_LED_tube_light_teardown.php
Aliyah the Gamer Girl says:
Wonderful, that’s definitely what I was looking for! You just saved me alot of digging around
UK Web Design says:
Great post but no joke the large amount of adesense ads really make our experience much less.
chiponboardled says:
(cob) Chip On Board LED Modules Lighting Solutions OEM lighting Manufacturers.
(10-100)% Dimmable LED Downlight
♥ LED Down Light Using a Chip On Board LED (COB LED) light source
LED Bulb Dimmable 10%-100% or not Dimmable
♥ Provides the greatest benefits for producing homogeneous light effects and high luminous densities .
LED Light Bulb Dimmable 10%-100%
♥ LED Light Bulb Using a Chip On Board LED Module light source
LED Bulb Dimmable 10%-100% or not Dimmable
♥ Excellent heat dissipation design , surface temperature is lower 55°C , Junction temperature lower than 102°C .
COB LED Light Tube T5 T8 T10
♥ LED Tube Using a Chip On Board LED Module light source
♥ T5 T8 T10 Tube Use COB LED,Light from area instead of spot, Which can avoid uncomfortable glare.
♥ No strobe. No continuous glow.
COB LED Spotlight MR16 GU10 E14
♥ LED Spotlight Using a Chip On Board LED Module light source
♥ Very low thermal impedance,excellent durability and stanbility at high temperature.
♥LED Spotlight High efficiency and PF factor AC-DC power supply
LED ALADDIN LIMITED
http://www.LEDaladdin.com
http://www.ledaladdin.hk/
e-Mail: [email protected]
Add: 4Floor Hongteng Building,392# Xihong Rd. Gulou District,
Fuzhou 350002,Fujian,China.
Tel: +86 591 6310 1956 Fax: +86 591 2285 5952
Replacing fluorescent lamp with LED « Tomi Engdahl’s ePanorama blog says:
[...] fluorescent lamp with LED The idea if replacing fluorescent light bulbs with LEDs seems to become popular. There are different kind of products made for that purpose, some are good [...]
Pennie Heddins says:
I really liked your blog post.Thanks Again. Great.
37 led says:
I haven’t checked in here for some time because I thought it was getting boring, but the last few posts are great quality so I guess I will add you back to my daily bloglist. You deserve it my friend
Edna Klich says:
Rattling great information can be found on blog . “You don’t get harmony when everybody sings the same note.” by Doug Floyd.
custom usb says:
Really looking forward to read more. Want more.
beffo says:
Really enjoyed this blog post.Really looking forward to read more. Want more.
Kitty Bede says:
I simply want to say I am very new to weblog and definitely savored you’re web blog. Most likely I’m going to bookmark your website . You definitely come with awesome posts. Thank you for revealing your website.
Tomi Engdahl says:
Slideshow: LED Lighting Teardowns
http://www.edn.com/design/led/4390501/Slideshow–Tearing-it-apart-What-s-inside-LEDs–?cid=EDNToday
What’s inside: LED tube light teardown
sdfgdnivvf says:
I was just not a fan at all. It didn’t really show up at all. I will be returning this tomorrow ,Mac Makeup Cheap
fatete dentare says:
Thanks for another magnificent post. The place else could anyone get that type of information in such an ideal manner of writing? I have a presentation subsequent week, and I’m at the search for such information.
watch dogs beta says:
At this time it appears like Drupal is the preferred blogging platform available right now. (from what I’ve read) Is that what you’re using on your blog?
tomi says:
I use WordPress.
Coy says:
I every time spent my half an hour tto read this blog’s articles daily along with a cup of
coffee.
Tomi Engdahl says:
Osram claims world’s most efficient LED lamp
http://www.edn-europe.com/en/osram-claims-world-s-most-efficient-led-lamp.html?cmp_id=7&news_id=10003737&vID=1597&from_mail=1#.UzkLCoVM0ik
An Osram research team has claimed to have succeeded in constructing the most efficient LED lamp in the world which achieves an efficiency level of 215 lumens per watt.
The lamp in tubular form consumes only half the power of current common fluorescent and LED tubes, and also achieves significantly superior colour rendering.
The device consumes 19W.
Johne46 says:
Only wanna tell that this is very useful , Thanks for taking your time to write this.
LED grow lights says:
My brother recommended I might like this web site. He was totally right.
This post truly made my day. You cann’t imagine just how much time I had spent for this information! Thanks!
t5 grow lights reviews says:
WOW just what I was searching for. Came here by searching for using t5 grow lights
free-dc.org says:
Light this time is reflected on inclusions positioned parallel with each other.
In the fashion market of India, there is huge market to be tapped.
Apart from being used in jewelry making quartz beads are used in making watches, radios, and in numerous mechanical devices as oscillators.
grow light says:
Hello! I just wanted to ask if you ever have any issues with hackers?
My last blog (wordpress) was hacked and I ended up
losing months of hard work due to no data backup. Do you have
any solutions to stop hackers?
Tomi Engdahl says:
First thing is to take care of the backups. Be prepared that you can get hacked and know how to repair site from backups.
Thing two is to keep WordPress up to date. Update it quickly when any security issues pop up in WordPress news.
Issue three is to keep your server setting right. Use good passwords and settings safe…
Step four: Check other things that can help. For example application level firewall modsecurity…
Tomi Engdahl says:
Led light tubes are the first and so far the only LED lamps format, which has received international harmonized standard. IEC approved E N 62776 – the standard for many years after twisting in mid-December 2014.
Standardization allows for traditional T8 fluorescent tubes are compatible with LED light tubes. In addition, the standard defines the characteristics of LED light tube, so that they are compatible with each other.
The new standard of the old fluorescent lighting tubes can be exchanged with one of led light tybe. The standard also defines the characteristics required of a light pipe, such as mechanical strength, physical dimensions and electrical characteristics. It also describes the products of the required marks and uniform testing practices.
Source: http://www.etn.fi/index.php?option=com_content&view=article&id=2311:ledivaloputki-sai-oman-standardin&catid=13&Itemid=101
Led Tube Lights says:
Thank you for sharing Led diagram with us .
thanl you so much .