LEDs and dimmers

Using existing triac controllers and wiring offers a number of challenges for LED lighting. To maximize the success and adoption of solid-state lighting for retrofit lamps, the LED lamps should be capable of dimming when used with existing controllers and wiring.

Lighting designs with flicker-free LED dimming article explores the typical TRIAC dimmer, some of the challenges of using it with LED lighting, and two interesting new power management solutions that solve these issues.

A common lighting dimmer available today is the leading-edge TRIAC dimmer. For an LED lamp to be dimmable, the lamp’s power supply must interpret the variable phase angle output from the TRIAC controller to monotonically adjust the constant current drive.

The difficulty of achieving this while keeping the dimmer working correctly may result in flickering, audible noise, and blinking as the light level is adjusted. These are generally caused by a combination of false triggering or premature shutdown of the TRIAC and inadequate control of the LED current. For reliable dimming down to low levels, the TRIAC must remain conducting almost to the point where the AC voltage falls to zero.

25 Comments

  1. lcd digital signage says:

    led dimer can save mucm power, and it is green method.

    Reply
  2. Tomi Engdahl says:

    Samsung LED light bulb teardown includes objective dimming numbers
    http://www.edn.com/blog/PowerSource/41611-Samsung_LED_light_bulb_teardown_includes_objective_dimming_numbers.php

    Notice that the incandescent bulb (yellow line) does not dim linearly with power. It’s main achievement is that it does dim down to zero. A CFL does a better job of dimming with power, and the Samsung LED light is very good, dimming quite linearly with power. However, it drops out at just under 20% of its max output light. (Which, however, more than meets the L-Prize spec.)

    Reply
  3. Tomi Engdahl says:

    Efficient dimming for LED lighting
    http://www2.electronicproducts.com/Efficient_dimming_for_LED_lighting-article-FAJH_Energy_Mar2012-html.aspx

    Lighting control with traditional TRIAC need not cut efficiency

    Using LEDs for lighting is an ever-more-popular application because of its high efficacy and long life. Dimmable lighting applications in residential and commercial installations will account for over 50% of all lamps and luminaires by 2015. There is wide installation of a variety of dimmers for traditional incandescent lighting, so LED-based light lamps and luminaries must be compatible with these dimmers.

    Fluorescent-based lamps and LED-based lamps today provide similar efficacies, but LEDs have a slight advantage.

    To properly trigger a TRIAC dimmer, the LED driver must provide a path that is independent of the driver’s input capacitance. This current path should be disabled once the TRIAC dimmer is conducting to avoid unnecessary power dissipation. The LED driver must also provide sufficient holding current to prevent the TRIAC-based dimmer from falling out of conduction and causing phase angle misinterpretations and potential flickering.

    Reply
  4. Tomi Engdahl says:

    Cirrus tackles dimmer compatibility challenges with digital LED controller
    http://www.edn.com/blog/PowerSource/41715-Cirrus_tackles_dimmer_compatibility_challenges_with_digital_LED_controller.php

    Cirrus Logic’s initial entry into the LED lighting market indicates that the company believes the key to success in this highly-competitive sector lies in achieving near-100% compatibility with the existing base of old-fashioned TRIAC dimming switches. The company has tested its new CS161X LED controller family, based on Cirrus’ new digital TruDim technology, with over 200 dimmer switches from around the world, and says the controller achieved 97percent compatibility

    According to Cirrus, the closest competitive LED controller performed at 71%, and the average among today’s current LED controllers was 50% compatibility.

    The CS161X’s digital intelligence allows the controller to identify the type of dimmer in use and adapt its dimmer compatibility algorithm to provide smooth dimming that mimics the response of an incandescent bulb, a response not possible with analog controllers.

    Just how important is dimmer compatibility? The US Department of Energy and its Energy Star program clearly believe it to be important: Dimming compatibility was a requirement for the Department’s L-Prize LED bulb competition, but it didn’t set the bar too high: Contest rules stated only, “Must be compatible with at least three widely available residential dimmers.” In addition, dimming switches are most prevalent in the US, especially California, and relatively un-common in Asia.

    Interestingly, the newer, so-called “digital” dimmers are the most difficult dimmers to ensure compatibility. The Maestro digital dimmer from Lutron can routinely make LED bulbs fail, while the old-style dimmers pose less of a challenge. (The “digital” refers to the ability of the switches to set and remember dimming levels; they still use the familiar TRIACs to chop the ac wave signal.)

    Reply
  5. Inteled says:

    Very interesting page.

    Reply
  6. Leds Screen Manufacturer says:

    Interesting but unfortunatly short article.

    Reply
  7. Tomi Engdahl says:

    Control device simplifies LED dimming
    http://www.edn.com/electronics-products/other/4442960/Control-device-simplifies-LED-dimming?_mc=NL_EDN_EDT_EDN_productsandtools_20161107&cid=NL_EDN_EDT_EDN_productsandtools_20161107&elqTrackId=94c8dcd2965244bcba255bd30c829bdc&elq=98986146868c4d3dbc1060889388a3d6&elqaid=34695&elqat=1&elqCampaignId=30283

    Inspired LED’s Triac Analyzer allows low-voltage LED systems to be controlled using almost any standard triac wall dimmer with a 12-VDC or 24-VDC plug-in power supply. The compact device applies a voltage to the dimmer and determines how long the dimmer takes to start conducting current. The amount of time is directly proportional to the position of the dimmer’s slide, and the Triac Analyzer adjusts the output to the LEDs accordingly.

    The Triac Analyzer serves as a cost-effective alternative to conventional hardwired systems, but still offers customers the flexibility to adjust their lights from a standard wall dimmer.

    TRIAC Analyzer
    http://www.inspiredled.com/low-voltage-triac-analyzer

    Reply
  8. Tomi Engdahl says:

    Lamp Dimmers – Leading and Trailing Edge
    https://www.youtube.com/watch?v=EDmXiG5AvSQ

    A demonstration of the difference between leading edge dimmers and trailing edge dimmers using an oscilloscope.

    Reply
  9. Tomi Engdahl says:

    Dimmer Power Factor and Variac Dimming
    https://www.youtube.com/watch?v=HDz4d1QdXBI

    What happens to power factor when phase cut dimmers are used, and a demonstration of using a variable transformer to dim incandescent and LED lamps.

    Reply
  10. Tomi Engdahl says:

    LED component itself is very well dimmable just by adjusting current through it with adjustable current limiting circuit and/or PWM control. LED itself dims “better” than traditional light bulb filament.
    The mains powered LED bulbs are not generally not well dimmable due limitations of the designs of the traditional light dimmers and power supply design on those mains powered LED bulbs.

    Reply
  11. Tomi Engdahl says:

    The SMPS for LED can’t be normally controlled by light dimmer because both are ‘chopper’ in nature. Those two devices can interact with each other in unexpected ways when connected together (depends on their exact designs and dimmer settings what happens).

    There are special dimmers that are designed to work better than traditional dimmers with LED bulbs – they will still not work with all LED bulbs.

    There are LED bulbs designed to be dimmable with normal light dimmers – they work with some traditional dimmers usually at some limited dimming range.

    Reply
  12. Tomi Engdahl says:

    RGB dimmer teardown and schematic (no microcontroller)
    https://www.youtube.com/watch?v=0WHFwqzyu0U

    This must be the first time I’ve ever referred to the humble 555 as a microcontroller. To be fair, it does have 8 pins and runs at 5V. Maybe a few less transistors though.

    Huge processing-power errors aside, this is an interesting and different use of the 555 from normal.
    It doesn’t use the main output pin, but instead uses the standard configuration to provide a triangular waveform directly from the capacitor.

    This is a very retro circuit, but it works well and is fully serviceable at every level, with scope for customisation in terms of PWM frequency and potentiometer range.

    Reply
  13. Tomi Engdahl says:

    Convert AC Voltage Regulator to DC Voltage Regulator
    https://www.youtube.com/watch?v=ouHg_FvE9iY

    Reply
  14. Tomi Engdahl says:

    Salt Water Dimmers
    https://www.youtube.com/watch?v=wRMEAYYW0dc

    In this video, we talk about the resistance dimmer’s predecessor, the salt water dimmer, which was basically a giant shock hazard that could also dim lights.

    Reply
  15. Tomi Engdahl says:

    LED (expensive) dimmer with dimmable and non-dimmable bulbs
    https://www.youtube.com/watch?v=ZfedtpTXIMI

    Reply
  16. Tomi Engdahl says:

    non dimmable LED dimmed
    https://www.youtube.com/watch?v=gfp4P3mTs5g

    Dimming a non dimmable led lamp

    So it is dimmable just does not use full range bc of forward voltage, thats fine by me

    Which dimmer was used?

    An industrial variac dimmer

    Reply
  17. Tomi Engdahl says:

    PWM 16A 3500W Triac Leading EDGE Dimmer
    https://www.tindie.com/products/bugrovs2012/pwm-16a-3500w-triac-leading-edge-dimmer-50hz-60hz/?utm_source=hackaday&utm_medium=link&utm_campaign=fromstore

    PWM 16A 3500W Triac Leading EDGE Dimmer 50HZ 60HZ High Current Arduino Raspberry V3.0 FreeDS UPSHIELD

    Leading Edge AC Light Dimmer 16A Arduino Raspberry
    https://www.youtube.com/watch?v=rpdOVpx1jIE

    Reply
  18. Tomi Engdahl says:

    https://www.facebook.com/groups/2494694997417025/permalink/3496426077243907/

    ABB Jussi kierrettävä triac-valonsäädin täysin sekaisin himmennettävän LED-lampun kanssa. Tutkimuksissa selvisi, että perinteisellä himmentimellä jännitteen nousureuna on liian nopea ja LED-lamppu imaisee yli 1,4A piikkivirtaa joka laukaisee himmentimen ylivirtasuojan ja koko homma alkaa värähdellä. Lopputuloksena 11W LED-lamppu imee jopa 13,5 Wattia sähköä ja silti palaa himmeästi.

    Ratkaisuna olisi vaihtaa jättöreunan himmennin, jollainen löytyy myös ABB Jussi sarjasta mutta valitettavasti sen käyttölogiikka on muutettu järjenvastaiseksi eli sitä pitää sekä painaa (on/off) että kiertää (säätö) kun meidän kaikki olemassaolevat valosäätimet toimivat pelkästään kiertämällä. Joskus aiemmin oli käytössä noita paina/kierrä sekasikiöitä ja ne hajosi kaikki tosi nopeasti ja niitä ei enää haluta!

    Tietääkö kukaan pelkästään kiertämällä toimivaa jättöreunan valosäädintä joka toimii ilman nollajohdinta? Clas Ohlson möi aikoinaan Cotech merkkistä, pelkästään kiertämällä toimivaa joita meillä on käytössä kaksi. Nämä toimivat LED-lamppujen kanssa oikein. Mutta jottei ratkaisu olisi helppo niin arvatenkaan näitä ei enää saa mistään! Monta vuotta vanha tuote…

    Hätäapuratkaisuna voisi olla myös pelkästään painamalla toimiva himmennin – eli luovutaan potentiometrisäädöstä, sikälimikäli niissä olisi sitten jotenkin järkevä käyttölogiikka.. ei kokemusta.

    Ja mitään puhelimella leikittäviä valoja ei haluta!

    Reply

Leave a Reply to Inteled Cancel reply

Your email address will not be published. Required fields are marked *

*

*