There are many cases when need to emulate various networking conditions and scenarios. Usually the most practical way to test the application on different networking conditions is to use some kind of WAN emulator that lets you control the various networking characteristics. WANem is a free WAN emulator suitable for this task. WANem allows the application development team to setup a transparent application gateway which can be used to simulate WAN characteristics like Network delay, Packet loss, Packet corruption, Disconnections, Packet re-ordering, Jitter, etc.
WANem is a Wide Area Network Emulator that is designed to provide a real experience of a WAN/Internet during application development and testing. WANem works over an Ethernet LAN environment. WANem is available in bootable CD and VMware virtual appliance versions at an affordable cost (for FREE!). Award winning (FOSS INDIA AWARDS 2008) WANem is built on top of Linux and many open source component. From a functionality perspective WANem hooks into the Linux kernel towards provisioning the network emulation characteristics and extends the functionality with additional modules.
Setup is pretty straight forward. WANem is normally launched through a LiveCD, which is based on a re-mastered Knoppix. Another option is to use VMware virtual appliance. I have used both versions. Both versions allow a quick and easy setup in any development environment with an intuitive web interface for purposes of configuration. You don’t need to be a network and Linux guru to use WANem because the provided easy and very quick. There are many example configurations you can easily select and you can modify them as needed.
In advanced mode you have option to set all necessary network performance parameters you can think of. If you are a networking expert and know what are the right setting for different parameters, this is the way to go. You can see the supported settings (in advanced mode) on the picture below.
WANem has even tool (WANalyzer is distributed along with WANem) that allow you to measure the performance of an existing real network, and then it can simulate how that network performed.
WANem has to be located between two hosts, between each we want to simulate a network link. The routing parameters which need to be configured on the clients and/or on the WANem machine. The preferred and most straightforward configuration uses a PC with two Ethernet cards and connect that between the two hosts.
It is possible to work also with only one Ethernet card (with some limitations), but for this to work you need special configuration on the end hosts to make sure all traffic they send gets sent to the WANem machine that forwards the traffic to other host. I have personally used this approach only when I have wanted to use the virtual machine version of WANem.
Installing and Configuring WANem Virtual Appliance and Using the WANem WAN Emulator Virtual Appliance articles tells that setup is pretty straight forward. After the WANem Virtual Appliance has been started and setup in your network environment, all you have to do is to route your traffic through it.
WANem is an excellent tool.
8 Comments
Hitleap website traffic says:
It is the best time to make a few plans for the future and it is time to be happy. I have read this submit and if I may just I desire to suggest you few interesting things or suggestions. Maybe you can write subsequent articles referring to this article. I desire to learn even more things about it!
repair service in the Tampa FL area says:
I know this web page presents quality dependent content and extra stuff,
is there any other website which provides such information in quality?
world freedom ventures says:
Have you ever thought about adding a little bit more than just your articles?
I mean, what you say is fundamental and everything. But imagine if you added some great graphics or video clips to give your posts more, “pop”!
Your content is excellent but with pics and videos, this blog could certainly be one of the best in its field.
Wonderful blog!
craft arrangements says:
Howdy would you mind letting me know which webhost you’re using?
I’ve loaded your blog in 3 different internet browsers and I must say this blog loads a lot faster then most.
Can you recommend a good web hosting provider at a honest price?
Thanks a lot, I appreciate it!
tomi says:
I am hosting this site in Amazon cloud.
Tomi Engdahl says:
Emil Protalinski / VentureBeat:
Facebook open-sources Augmented Traffic Control, a Wi-Fi tool for simulating 2G, Edge, 3G, and LTE networks
http://venturebeat.com/2015/03/23/facebook-open-sources-augmented-traffic-control-a-wi-fi-tool-for-simulating-2g-edge-3g-and-lte-networks/
Facebook today open-sourced Augmented Traffic Control (ATC), a Wi-Fi tool for testing how mobile phones and their apps handle networks of varying strength, over on GitHub. ATC simulates 2G, Edge, 3G, and LTE networks, and allows engineers to switch quickly between various simulated network connections.
ATC came into existence after years of attempts, mostly at Facebook hackathons (starting in January 2013), to create test network conditions that simulate what users experience in the real world. Since Facebook wants as many people as possible to access its services at their full potential, it follows that the company should be able to test on wireless connections that more accurately reflect those that many ultimately use.
Augmented Traffic Control: A tool to simulate network conditions
https://code.facebook.com/posts/1561127100804165/augmented-traffic-control-a-tool-to-simulate-network-conditions/
We created Augmented Traffic Control with open source technology, building on the work of others. We want to give the open source community the same chance to improve on our ideas and innovate with their own — so today we are open-sourcing our design for Augmented Traffic Control on GitHub.
https://github.com/facebook/augmented-traffic-control
minecraft says:
Wow, that’s what I was exploring for, what a stuff! existing here at this blog,
thanks admin of this web site.
Tomi says:
https://hackaday.com/2024/01/17/modeling-network-latency/
https://github.com/kffl/speedbump