DMX 512 control board DMX 192 repair

DMX stands for Digital Multiplex DMX512 (Digital Multiplex) is a standard for digital communication networks that are commonly used to control stage lighting and effects. DMX can now be used to control almost anything, reflecting its popularity in theatres and venues. I have some DMX-512 controlled lights and also built some DMX-512 hardware myself.

I have used some computer controls and some very simple desks for light controlling earlier. There have been times where I have wanted to have a programmable DMX-512 desk with at least eight sliders that would not cost to much. I saw Lixada 192 Channels DMX512 Controller Console for Stage Light Party DJ Disco Operator Equipment for sale at very low price (below 30 Euros). So it looked like an attractive deal especially as this type of desk is widely sold under various brands. It might not be the best, but could be at least half-decent and useful. I looked some videos on YouTube, and based on them it looked OK.

I finally got the desk and it looked OK and buttons seemed to work.

20210305_212751

Then I started testing using the manual and some introductory videos like this.
DMX 192 Controller Unboxing and Programming

I did lot’s of testing. The controls seems to work, but I was unable to get any of my DMX-512 equipment to work with it. It seems that there is no signal coming out of the back of the unit no matter what I did. I even measured the signal coming from the back of the unit, and did not get any consistent results, sometimes no signal at all, sometimes only from either pin 2 or 3. Not valid RS-485 signal levels. My DIY DMX signal tester did not show any useful signal. I also tested signal with multi-meter and oscilloscope.

I got money back after I posted them a video how their board does not work and it should. They did not want their crap back, so I got to keep the non-working device. Next task was to open device to see what is inside it and maybe even fix it.

20210305_212727

20210305_212724

The bog circuit board has all the controls and the “brains”. There is a smaller IO board that has connectors. There is four wire cable between them that carries 9V power in, 5V power, ground and transmitted data.

Here is a closer look at connectors board. It seems that the problem could be somewhere here.

20210305_203534

20210305_212336

20210305_212336

20210305_212340

Problem seems be that this board does not seem to not work.. The board is pretty simple with RS-485 line driver chip, some other components and connectors. A quick probing seems to indicate that the RS-485 driver works OK, but the signals for some reason did not get to output connector properly.

Looked what would be problem by more probing the circuit, trying to look what goes where, try to look component codes and measure passive component not clearly marked. After some probing I draw this basic idea how the DMX-512 driver output works. There seems to be some over-voltage protection components and some series resistors to connector.

20210313_142636

Based on my fault-finding it looks like there is completely wrong resistor values compared to what they should be. Those two 200 ohm resistors will pretty much screw up the output impedance matching and cause signal to be attenuated a lot when the DMX-512 line is properly terminated with 120 ohm resistor. Those series resistors if they are used should have much lower in value to no cause issue. For example in this mutisemi application example picture those resistors are 0-10 ohms:

screenshot_20210313-161243_chrome

Finally I tried a fix with short jumper wires over those 200 ohm resistors bringing them close to 0 ohms.

20210313_141238

After this modification I got the board to work nicely. It worked with the light I had, bot with and without DMX-512 terminator on the line. The board worked nicely with quite long cables as well (100 meters of CAT 5E UTP). So this fix made the board to work well. I think that there has been some manufacturing error on the factory that made this product so that they had put wrong value resistor to the board and for some reason the product testing did not catch this error for some reason. The potential downside of this modification is that the surge protection on the DMX-512 output might not be as effective as it was originally designed to be (small resistors between connectors and zeners will absorb surge energy more than short circuit before it hits the zener diodes and the driver chip).

On the basic tests the board seemed to work well. I have not tested all the board features. I am planning to view again some more videos on using the board to learn how to use it well:

How to Program DMX lights – SCENES CHASES & BANKS w Rockville ROCKFORCE 192

Lumin Lights 192 DMX Controller Mixer Mixing Board Light Controller

How to program DMX lights for beginners (simple lesson)

Simple DMX Programming (part 2)

How to Program a Mini Moving Head: Simple and Cheap

14 Comments

  1. Tomi Engdahl says:

    Make Your Own DMX Signal Tester
    https://www.youtube.com/watch?v=wLC3ojYHd70

    DIY keychain DMX tester for lighting technicians.
    https://www.youtube.com/watch?v=skwUNRp-Rrk

    Reply
  2. Tomi Engdahl says:

    How to make a DMX Terminator with built in Tester
    https://www.youtube.com/watch?v=tdSK5coyvvc

    Reply
  3. Tomi Engdahl says:

    I once considered building something like this before I go my hands on this very cheap light control desk…

    Arduino DMX 512 Tester and Controller ENG
    https://www.instructables.com/Arduino-DMX-512-Tester-and-Controller-ENG/

    Control tool for testing and light show by the DMX-512 protocol, ideal for quick tests on fixed or temporary installations of lighting. This project arises from the need to have a portable system for rapid testing in lighting installations, without the need to install lighting consoles, interfaces or computers in environments outside, hostile or difficult to access.

    Arduino DMX-512 Tester Controller © GPL3+
    Control tool for testing and light show by the DMX-512 protocol, ideal for quick tests on fixed or temporary installations of lighting.
    https://create.arduino.cc/projecthub/daniel3514/arduino-dmx-512-tester-controller-977c89

    Reply
  4. Tomi Engdahl says:

    Did something like this happen on the manufacturing?

    Fail Of The Week: Mistaking Units For Values
    https://hackaday.com/2021/04/24/fail-of-the-week-mistaking-units-for-values/

    Reply
  5. Tomi Engdahl says:

    No real life mic cable you can buy has really 600 ohms impedance. Practical mic cables have typically impedance in 40 ohms to 150 ohms range.

    “Standard analog audio cable impedance is 45 Ohm to 70 Ohm.”
    Source: https://beldencables-emea.com/en/products/pro-broadcast-products/audio_cables/index.phtml

    Reply
  6. Tomi Engdahl says:

    DMX (and AES) cable is 110 ohms.

    Not a serious problem to interchange with mic cable on very short runs, but long runs/lots of cables jumped together causes problems

    Reply
  7. Tomi Engdahl says:

    “in a pinch you can definitely use short runs of three pin xlr and mic cable in place of DMX type 5 pin.”

    Yes.

    “Regular mic cable has basically no insulation and DMX is very susceptible to interference….”

    I have to disagree somewhat with this. Normal mic cables have typically quite good insulation and good shielding – in many ways ok for DMX.
    The most serious problems are typically related to wrong cable impedance (causes signal attenuation and bit errors on long runs). Sometimes the cable insulation materials can cause extra signal attenuation. And ground loops can cause issues.

    Reply
  8. Tomi Engdahl says:

    DMX 192 Controller Unboxing and Programming
    https://www.youtube.com/watch?v=zyV1CjHoJ2U

    How to program DMX lights for beginners (simple lesson)
    https://www.youtube.com/watch?v=dJQAZsNwcv4

    Reply
  9. Tomi Engdahl says:

    CO-Z 192 DMX Controller – A review, demo and how to start creating DJ Light Shows w/o over spending.
    https://www.youtube.com/watch?v=DetjcLviGAg

    Reply
  10. Tomi Engdahl says:

    So You Want To Get A DMX Board For Under $50 – CO-Z 192 review
    https://www.youtube.com/watch?v=QynCoLUkQHc

    How to Program DMX lights – SCENES CHASES & BANKS w Rockville ROCKFORCE 192
    https://www.youtube.com/watch?v=jFIKWoPcZGI

    Reply
  11. Tomi Engdahl says:

    How to program DMX controller 512 for beginners
    https://www.youtube.com/watch?v=zyV1CjHoJ2U

    Reply

Leave a Reply to Tomi Engdahl Cancel reply

Your email address will not be published. Required fields are marked *

*

*